The racing-two-seater EB29DR

EB29DR double-seater EB29D with performance-optimized R-wing

- completly new design of wing geometry to the edition wing
- lower wing aerea for higher wing load
- new wing profile with lower hight
- outlow over the intire span

The newly developed profile allows good performace in high-speed range and good circling properties at high wing loads. High modulus fiber in the complete wing shell produces a very high stiffness, wich is characteristic in fast flight.

But this is not the end of the development. Further model maintenance and performabnce optimization of recent years:
- the tailwheel is now electrically retractable and in addition steerable
      for better  ground handling
- the rudder actuation levers are now integrated into the fuselage and thereby
      the scoops at the tail fin and the rudder are no longer needed
- profile change of the nose at the fin
and last but not least
- the HLW2020 - an entire new elevator with a new airfoil and reduced area

technical data

wing span28 m
wing area14,9 m²
aspect ratio52,62
fuselage length8,32 m
hight (fin plus tail wheel)1,76 m
emty mass with minimal equipmentca. 615 kg
maximum ramp weight850 kg
wingloading minimumca. 47,5 kg/m²
wingloading maximum57,5 kg/m²
maximum speed270 km/h
best glide ratioca. 66
Solo engineca. 63 PS
FRP-prop Binder BM-G1d 1,6 m
rate of climb with engine (according ICAO standard athmosphere)2,6 m/s
cruise speed in powered flightmax.160 km/h
max useable tank capacity (standard)20 ltr
Datasheet  EASA A.559

description

fuselage:

  • body shell made of fibre reinforced plastic (CFK and aramide)
  • cockpit suitable for pilots up to 190 cm in the front seat and little less in the rear seat
  • forward swinging canopy including one sliding window with integrated ventilation scoop
  • instrument panel moves upward with the canopy
  • TOST-safety release couplings (for aero tow or winch tow)
  • total pressure probe in tip of the fuselage nosecone
  • adapter in the fin to fit TEK probe
  • static pressure probes (for air speed indicator and altimeter) on both sides of the tail boom

cockpit:

  • removeable bucket seats with parachute mould in the front seat
  • safety belts
  • seat cushions
  • 2 side Pockets (rear seat)
  • ram air entrance in the nosecone of the fuselage for ventilation and defogging of the canopy
  • seperately controllable ventilation for both seats on right side of the cockpit

controls:

  • rudder control pedals on linear rails (adjustable before flight)
  • control rods made of CFK
  • electrically adjustable trim with operating switches on both control sticks
  • automatic elevator connection

landing gear and brake:

  • rubber suspended, electrically operated retractable landing gear
  • hydraulic disk brake
  • tail wheel

power plant:

  • power plant retractable into the fuselage
  • solo engine 2625/2
  • tooth belt driven reduction gear (1:3)  
  • water cooling
  • double ignition
  • electrical starter
  • LiMg-batteries with 16,8 V max charching voltage for improved extension and retraction as well as starting of the engine
  • engine control instrument fitted to the instrument panel
  • Propeller Binder BM-G1-160-R-120-1

fuel tank:

  • fuselage tank ~20 ltr

antenna:

  • radio antenna in fin

wing:

  • 6-part wing with boundry layer control on the lower wing surface
  • built using high modulous (HM) carbon fibre
  • aileron and flap gaps covered with Mylartape
  • double panel air brakes on the upper wing surface

water ballast:

  • water ballast bags in the outer wings ca. 35 ltr capacity each
  • water ballast tank in the fin to allow for compensation of CG-movement using water ballast in the wings

finish

  • white two component plyester coat or PU-coat

 

To minimize the structural weight the main parts of wing and fuselage are built using the vacuum suction method. This allows the utmost possible spread in wing loading.


EM 2023 Leszno Poland

21th FAI European Gliding Championships -... [more]

DM 2023 Bayreuth

The German Nationals 2023 of the Open Class, the... [more]

WGC 2022 Szeded

37th FAI World Gliding Championships 2022 –... [more]

Binder Motorenbau GmbH
Alter Frickenhäuser Weg 15
D-97645 Ostheim v. d. Rhön

Tel.: +49(0)9777 - 9200

binder.motorenbau(at)t-online.de

HB DE.21.G.0138
DE.CAO.0089
LBA.MG.0534